VideoHelp Forum




+ Reply to Thread
Results 1 to 13 of 13
  1. Member
    Join Date
    Oct 2026
    Location
    Los Angeles
    Search PM
    Hi y'all - my Aiwa VCR, which up until today had been playing tapes without issue, has developed this static-positioned distorted horizontal line across all tapes I've tried. It actually appears more like clustered small vertical lines spread out horizontally across the screen. Standard play, EP or LP, commercial tapes/any tapes - some form of this distorted line exists, in the upper half of the screen.

    Here is a link to a video with an example of the problem - https://www.dropbox.com/scl/fi/o786mf9l0cl06kkjgw98u/20261022_213211_394_657.mov?rlkey...=w38u8h44&dl=0

    I have thoroughly cleaned the head and all guides and areas the tape interacts with. Adjusting tracking does not help. Some tapes worse than others, although haven't sorted out a pattern.

    Are one of the heads just wearing down? Possibly something deeper stuck there? Hoping there might be some insight from someone who has experienced this before.


    Cheers
    Quote Quote  
  2. Capturing Memories dellsam34's Avatar
    Join Date
    Jan 2016
    Location
    Member Since 2005, Re-joined in 2016
    Search PM
    If this was one tape I would say a scratch along the tape due to tape damage, but since it happens on any tape I would assume there is a misalignment or a mechanical problem, The DOC is trying to compensate for the signal loss but this would appear as a static noise bar if the DOC was not present, Another possibility is the VCR is damaging the tape as it plays it, I would still visually check the tape to make sure there is no damage.
    Quote Quote  
  3. Member
    Join Date
    Oct 2026
    Location
    Los Angeles
    Search PM
    the physical tape seems fine after playing, no apparent damage. are there adjustments I can make to alignment to check? i am used to working on cassette decks but have less experience with VCRs
    Quote Quote  
  4. Capturing Memories dellsam34's Avatar
    Join Date
    Jan 2016
    Location
    Member Since 2005, Re-joined in 2016
    Search PM
    You don't start messing with the alignment until you make sure there is no problems with the mechanism, Make sure there is no cracked gears worn or loose parts, the mechanism is clean and lubricated.
    The fact that your VCR was playing tapes without issues this is less likely to be an alignment issue and more likely to be a mechanical fault.
    Quote Quote  
  5. Member The_Doman's Avatar
    Join Date
    Feb 2004
    Location
    Netherlands
    Search PM
    Originally Posted by cpt.shotwell View Post
    Hi y'all - my Aiwa VCR, which up until today had been playing tapes without issue, has developed this static-positioned distorted horizontal line across all tapes I've tried. It actually appears more like clustered small vertical lines spread out horizontally across the screen. Standard play, EP or LP, commercial tapes/any tapes - some form of this distorted line exists, in the upper half of the screen.
    From my own experience , seeing this kind of line/distortion , it looks like typical tape damage.
    Probably something in the tape path causing this.
    You should not play any valuable tapes in that VCR from now on, until the problems have been fixed/determined.
    Of course, you should check the tapes on another VCR to verify.
    Quote Quote  
  6. Member
    Join Date
    Oct 2026
    Location
    Los Angeles
    Search PM
    Playing back the same section of the same tape on a different VCR and I see no issues with the picture.

    Aside from the guides, the erase head, the drum, audio heads... I've cleaned them all. Not sure what else I can check that's within the tape path.

    The reason I enjoy this Aiwa so much is due to the fact that it will play most any tape from any region and any video standard and convert it to whatever output you want as well. I had no issues with it for years, then just this week the distortion occurs.

    Is there some deeper cleaning I should be doing on the drum that might help?
    Quote Quote  
  7. Capturing Memories dellsam34's Avatar
    Join Date
    Jan 2016
    Location
    Member Since 2005, Re-joined in 2016
    Search PM
    Check the P guides, Do they turn freely if you try to turn them by finger from the top slit, If so then your alignment is lost. Another check, when the tape is fully laced, unplug the power cord, wait for the drum to spin down and check the guides by hand they should be firm, if they wiggle they are broken, these are examples of basic checks, there is a lot more to check, this is why VCRs have techs to work on them just like cars.
    Quote Quote  
  8. Member
    Join Date
    Oct 2026
    Location
    Los Angeles
    Search PM
    performing this check, the guides are taught and fixed firm when the tape is fully laced and the power cut/drum slowed down. when the tape is ejected and the guides are back down, there's some play to them, but i believe that's normal?
    Quote Quote  
  9. Capturing Memories dellsam34's Avatar
    Join Date
    Jan 2016
    Location
    Member Since 2005, Re-joined in 2016
    Search PM
    Yes that's normal, they only lock up at the end of their travel when the tape is fully laced, What about the P guides' rollers, do they turn loosely by hand? Not the plastic sleeve, that should spin freely, I'm talking about the top flange that has a slit for a special screwdriver adjustment, it should have some red sealant and should be firm if you try to spin it gently with your fingers.
    Quote Quote  
  10. Member
    Join Date
    Oct 2026
    Location
    Los Angeles
    Search PM
    okay well! it appears I've found the issue. just for reference for any future viewers.

    i had already cleaned most of it off, but went back to try to take a photo of the issue. in the attachment you can see on the fixed part of the drum circled in red that has some tape residue or corrosion or gunk of some sort that had fixed itself there. just cleaning from the outside and the heads wasn't sufficiently reaching in between that tiny gap to get that junk out.

    so i scraped a bit off with some tweezers and then got in there with some IPA again. distortion is gone!

    so it was hidden gunk. its really true... just make sure the thing is CLEAN.

    thanks for your guidance and suggestions
    Image Attached Thumbnails Click image for larger version

Name:	wij.jpg
Views:	7
Size:	101.5 KB
ID:	94353  

    Quote Quote  
  11. Member
    Join Date
    May 2005
    Location
    PAL User
    Search Comp PM
    Thanks for the update Cpt.
    Quote Quote  
  12. Originally Posted by cpt.shotwell View Post
    okay well! it appears I've found the issue. just for reference for any future viewers.

    i had already cleaned most of it off, but went back to try to take a photo of the issue. in the attachment you can see on the fixed part of the drum circled in red that has some tape residue or corrosion or gunk of some sort that had fixed itself there. just cleaning from the outside and the heads wasn't sufficiently reaching in between that tiny gap to get that junk out.

    so i scraped a bit off with some tweezers and then got in there with some IPA again. distortion is gone!

    so it was hidden gunk. its really true... just make sure the thing is CLEAN.

    thanks for your guidance and suggestions

    Yes, debris in that area can cause distortion of the picture.

    Anything in that area will interrupt/alter the air flow that is created by the rotating head assembly which will change how much air cushion there is between the tape, drum and heads.

    Short story on how this works is that the tape will float on a very thin cushion of air that gets created by the head drum spinning. The cushion must be uniform the entire path that the tape wraps the drum.

    The debris in the pix almost looks like crumbled foam from a foam cleaning swab that has aged out. Might wish to get some fresh swabs if that is what you are using. You got pretty lucky, get debris stuck in the tiny micro gap of the head and you will be looking for a replacement drum head as removing that is much more difficult to impossible to pull off.
    Quote Quote  
  13. Member The_Doman's Avatar
    Join Date
    Feb 2004
    Location
    Netherlands
    Search PM
    Originally Posted by GAhere View Post
    The debris in the pix almost looks like crumbled foam from a foam cleaning swab that has aged out.
    Or, even worse, an unremoved automatic head cleaner.
    Quote Quote  



Similar Threads