VideoHelp Forum
+ Reply to Thread
Results 1 to 9 of 9
Thread
  1. Hello. I'm copying my VHS tapes. Unfortunately, one cassette was damaged while rewinding. The tape was short (a few minutes), so the VCR sped up and wrinkled my tape. I am attaching photos of what it looks like inside the cassette.

    Some youtube videos advices to just cut damaged parts, but The tape is very short (a few minutes), so there is nothing to cut.
    Is there anything I can do to repair and straighten this tape without cutting?

    If it was any important cassette, I would take it to a specialist. But it's just an old commercial, so I'm looking for a way to know what to do in this situation in the future.

    Image
    [Attachment 66575 - Click to enlarge]

    Image
    [Attachment 66576 - Click to enlarge]

    Image
    [Attachment 66577 - Click to enlarge]

    Image
    [Attachment 66578 - Click to enlarge]
    Image Attached Thumbnails Click image for larger version

Name:	S1350099.JPG
Views:	37
Size:	1.04 MB
ID:	66571  

    Click image for larger version

Name:	S1350100.JPG
Views:	38
Size:	987.8 KB
ID:	66572  

    Click image for larger version

Name:	S1350101.JPG
Views:	46
Size:	1,003.1 KB
ID:	66573  

    Click image for larger version

Name:	S1350102.JPG
Views:	38
Size:	1,010.2 KB
ID:	66574  

    Quote Quote  
  2. Member Cornucopia's Avatar
    Join Date
    Oct 2001
    Location
    Deep in the Heart of Texas
    Search PM
    Put it on an ironing board, put a piece of fabric on top to reduce the heat a bit, and iron it out.

    But seriously (because the above could likely melt the tape), you're too late. Wrinkled is wrinkled. You can manually unroll it all (break off the hub tops if they are pinching the tape and keeping it from coming loose), and then properly reroll it onto a new, empty reel, and then put it into a vcr that doesn't eat tapes and run it through a few cycles of FF and RW, so it "packs" the tape nicely again with good even tension. Then let it sit for a while, which can help flatten it out better. But the wrinkles and creases will never go away completely after what has already happened.


    Scott
    Quote Quote  
  3. Originally Posted by Cornucopia View Post
    Put it on an ironing board, put a piece of fabric on top to reduce the heat a bit, and iron it out.

    But seriously (because the above could likely melt the tape), you're too late. Wrinkled is wrinkled.
    Not if temperature will be bellow tape melting point (i.e. common case for synthetic fabric ironing on first star/dot).
    And yes, wrinkled tape will stay wrinkled but it may wrinkled less and as such be (hypothetically) restored to shape where recording may be reconstructed.
    Reconstruction of course may be time and resources costly so in overall beyond sane sense...
    Quote Quote  
  4. Capturing Memories dellsam34's Avatar
    Join Date
    Jan 2016
    Location
    Member Since 2005, Re-joined in 2016
    Search PM
    You can iron it to ease the pressure on the playback drum and maybe reduce RF noise a little bit but the content are lost forever and can never be recovered to a noise free state, the VCR's DOC tries to reduce RF noise by replacing the noisy lines with the good adjacent ones but in the case of severe tape damage there isn't much that can be done about it.

    The other thing is that your VCR must have problems, The tell tale of eating tapes while fast forwarding or rewinding is worn out spindle brakes, When the spools are spinning fast and you hit stop both should stop immediately, if one continues to spin due to lack of brake pad material it will spill the tape and make a mess inside the VCR. Fix it or get rid of it.
    Quote Quote  
  5. Member
    Join Date
    Jul 2007
    Location
    United States
    Search Comp PM
    Even if you are able to iron out the wrinkles, there's a good chance you'll clog your videoheads because of the flaking oxide. Be prepared to clean your heads after playing the tape and hope no permanent damage has been done. *Replays the awful sound of videoheads playing a wrinkled tape* *SHUDDER*
    Quote Quote  
  6. Capturing Memories dellsam34's Avatar
    Join Date
    Jan 2016
    Location
    Member Since 2005, Re-joined in 2016
    Search PM
    The same sound a weed whacker makes when the strings hit a rock.
    Quote Quote  
  7. Video Restorer lordsmurf's Avatar
    Join Date
    Jun 2003
    Location
    dFAQ.us/lordsmurf
    Search Comp PM
    Originally Posted by dellsam34 View Post
    The same sound a weed whacker makes when the strings hit a rock.
    The sound of a slobbering dog, with long nails, running up inclined glass.
    Want my help? Ask here! (not via PM!)
    FAQs: Best Blank DiscsBest TBCsBest VCRs for captureRestore VHS
    Quote Quote  
  8. Thanks for answers.
    Luckily only first 1/3 of tape is damaged.

    This is my additional VCR for copying less important cassettes.
    I was very surprised when it's happened. It was working good before.
    Quote Quote  
  9. does this method really work i have a old wedding video of a family member on vhs tape been kept away for years other family members have handed it down over the years and then to me but the vhs tape is a little bit like this vhs tape above but it is wrinkled up at the bottom of the vhs tape. is there anyway to remove the wrinkles off the bottom of the vhs tape.
    Quote Quote  



Similar Threads

Visit our sponsor! Try DVDFab and backup Blu-rays!