I trust somebody would be able to help.
I am using IP cameras from two different suppliers in China namely MWR and Tenvis. I am also streaming this to Active Webcam V 11.5 and I am getting great results. ( As far as I am concerned this is great motion detection/recording software with very nice and handy features.)
The original problem was that AW 11.5 did not have any of these makes as a "standard" option so I had to search and experiment for quite some time to get the "setup string" for the cameras. I now get good results for video but so far have been unable to get the setup string for audio, especially for the Tenvis camera.
If I access the camera via IE I can get the audio as well but as I understand from the manufacturer, this is "built into" the software when using IE. ( Only IE works...but not Firefox )
Now, my question is:
Does any one have an idea how I should go about finding the string for the audio ? In the AW software there is a section to do the audio setup but I have no idea what this should be.
Help would be greatly appreciated !
Try StreamFab Downloader and download from Netflix, Amazon, Youtube! Or Try DVDFab and copy Blu-rays! or rip iTunes movies!
+ Reply to Thread
Results 1 to 7 of 7
Thread
-
-
Please, Can you show me the way to setup the video (TENVIS camera JPT3815W) with Active Webcam SW?
Thanks in advance -
Sorry for the belated reply.
The setup string in the camera interface window that you need for Tenvis in Active Webcam is :
http://192.168.0.253/?action=stream/?channel=1.mjpeg
Where the Ip address is that of your camera and the default username/p/w is admin/admin
Good luck ! -
Thanks for your answer
As far as I understand, I have to put in Active Webcam device setup window (see picture attached):
- Video Device:
Network IP Camera = selected
After this configuration, I think I have to push the button "Camera Interface" to access to new window
Camera Model = Unknown
IP address o URL= 192.168.1.239 (this is my ip configuration)
Port= 82 (this is my port)
User ID= mleon
Password=XXXXXX
- Network Camera Interface - General
Many many thanks If you can help me to configurate the cameraCamera Model= Unknown
Address of administration web page=
Address of Camera Web Page=
String to request JPEG image= http//192.168.1.239/?action=stream/?channel=1.mjpeg(I think I have to add my pesonal user/password to this sentence, but I don't know how)
String to reset Camera=
Use DLL to comunicate with camera= NO selected
In any case thank for your dedication
Regards -
You have the settings right !
You do not have to add un/pw to the request string as you already have this in the device window. After you have done the setup and the video works, then save the setup under the name "Tenvis' and you should be able to go back to the settings in future.
Your camera should stream video to the SW now. In my opinion the software is great but do not expect ANY support from the SW company. They simply do not reply to emails.
Just another tip......... When you view the camera video on your browser ( IE or Firefox ) , do a right click on the picture and view the source. You should then see the setup string as well.
Good luck !! -
After some "trials hours".....I can't get the video
Tomorrow will be another day
If you could waste some of your time, I can pass you the way to access to my IP cam
Regards -
New day...new ideas.......get solution
After checking all without success. I've detected some issues regarding firmware version in TENVIS IP camera
see http://forum.tenvis.com/thread-1933-1-1.html
So, I change the firmware from the new one (1.7.15) to the old one (1.7.10) and now...... it's works
Finally these are the sentence:
String to request JPEG image=http://{CAMERA_IP}/videostream.cgi?user={USER_ID}&pwd={PASSWORD}
Pan left ... http://{CAMERA_IP}/decoder_control.cgi?command=0&user={USER_ID}&pwd={PASSWORD}
Pan left stop ..... command=1
Pan right ...........command=2
Pan left stop ..... command=3
.......
Ok, thanks, if I can get audio I will inform you
RegardsLast edited by Mleon; 5th Mar 2013 at 17:41.
Similar Threads
-
Video Cameras: Tell Me What To Buy
By Orphonic in forum Camcorders (DV/HDV/AVCHD/HD)Replies: 12Last Post: 14th Sep 2011, 15:53 -
Editing video recorded with two cameras
By MI6 in forum EditingReplies: 3Last Post: 18th Feb 2011, 19:09 -
using photography cameras for video...
By nkordyjaka in forum Newbie / General discussionsReplies: 16Last Post: 31st Dec 2010, 18:14 -
Video cameras stop recording
By Coolboy55 in forum CapturingReplies: 5Last Post: 7th Nov 2008, 12:07 -
Flip Video Cameras
By guns1inger in forum Camcorders (DV/HDV/AVCHD/HD)Replies: 11Last Post: 19th Aug 2008, 18:24