VideoHelp Forum




+ Reply to Thread
Results 1 to 8 of 8
  1. 27th Jul 2002 20:38 #1
    devnulllore
    devnulllore is offline
    Member
    Join Date
    Jan 2002
    Search Comp PM
    Has anyone been able to get ATI's MMC to record in 480x480 mode for SVCD's?

    I can set Power VCD II to that resolution so it is a capability of the card.

    Not sure how to do it with MMC.
    ~dev
    Quote Quote  
  2. 27th Jul 2002 20:57 #2
    Mirror_Image
    Mirror_Image is offline
    Member
    Join Date
    Jan 2002
    Location
    State of Confusion
    Search Comp PM
    Try upgrading MMC to 7.7, it has an SVCD preset.
    As Churchill famously predicted when Chamberlain returned from Munich proclaiming peace in his time: "You were given the choice between war and dishonor. You chose dishonor, and you will have war."
    Quote Quote  
  3. 27th Jul 2002 21:04 #3
    devnulllore
    devnulllore is offline
    Member
    Join Date
    Jan 2002
    Search Comp PM
    I looked at 7.7 once and it said on the site that I cannot use it with my card.


    I have the ATI TV-Wonder PCI.

    Can I use it?
    ~dev
    Quote Quote  
  4. 28th Jul 2002 11:10 #4
    tjdmobile
    tjdmobile is offline
    Member
    Join Date
    Dec 2001
    Search Comp PM
    Have you tried Stinky's Registry tool (found on this site)? He has put a lot of great effort into creating 'templates' for creating high-quality SVCDs. You should check it out!

    I personally use his tool for setting the horiz. vert. motion search features. Saves time!
    Quote Quote  
  5. 28th Jul 2002 11:56 #5
    devnulllore
    devnulllore is offline
    Member
    Join Date
    Jan 2002
    Search Comp PM
    The reg tools worked I can make a profile for SVCD now. The problem is am I going to run into audio/video sync issues.

    Any suggestions to avoid this before I start?
    ~dev
    Quote Quote  
  6. 30th Jul 2002 10:46 #6
    tjdmobile
    tjdmobile is offline
    Member
    Join Date
    Dec 2001
    Search Comp PM
    From my experience (I don't use MMC 7.7 anymore), there are never any sync issues for me in MMC 7.6. Besides, it would appear to be a problem folks have if the audio / video clocks are slightly off.

    Hopefully it will go well for you (using his templates), but I have never had to re-mux using TMPGenc or other. I always cap directly to VCD / SVCD. Stay with CBR, it is less likely you would experience audio drift that way. I use VBR for everything, however, as I have not had any audio drift in MMC...

    PowerVCR II, however, is a different story. I can't figure out why I have such extreme audio drift with that application...
    Quote Quote  
  7. 31st Jul 2002 00:35 #7
    Jayloki
    Jayloki is offline
    Member
    Join Date
    Jun 2002
    Location
    Whitby/ont
    Search Comp PM
    Send a message via ICQ to Jayloki
    How do you get Stinkys program to work?? I unzipped it into a folder of its own and when i go to change profiles or load them etc etc...it says none are detected etc etc!! Can anyone help a newb get this program started?? Thanx.

    Do i have to install it to tha ati file fodler?? Thanx to anyoneon this simple question
    Quote Quote  
  8. 31st Jul 2002 00:56 #8
    DRfrankenpimp
    DRfrankenpimp is offline
    Member
    Join Date
    May 2002
    Location
    louisville,ky
    Search Comp PM
    you must first create templates and name them then launch stinkys reg tool and look for those and make your adjustments...templates must be mpeg
    Quote Quote  



Similar Threads

« Previous Thread | Next Thread »
Visit our sponsor! Try DVDFab and backup Blu-rays!